Raspberry Pi Stack Exchange
Raspberry Pi Stack Exchange

Questions tagged [fuses]

a Linux kernel module to handle file systems in Userspace.

11 questions
9
votes
1 answer

Should I Bypass the USB fuses on the revision 1 Raspberry Pi?

As blogged on raspberrypi.org, the USB fuses are no longer on some of the later revision 1 PCBs or the revision 2 PCBs USB Output Power The resetable fuses protecting the USB outputs have been removed. This feature was implemented on some later…
John La Rooy
  • 12,005
  • 9
  • 48
  • 77
6
votes
2 answers

Raspberry Pi Model B Revision 2, Max USB Output Power

With the rev. 2 of the Raspberry, the USB protective fuses are removed. Does this change increase the max current limitation of 100mA per USB? If not, what does imply the elimination of the fuses? Can the Raspberry be powered through the USB port…
Sergio Lopez
  • 85
  • 1
  • 1
  • 4
2
votes
1 answer

Is my raspberry Pi dead

I tried a circuit with raspberry pi to drive a motor, so there was 12 V at the circuit I used it with. I might have wired it in a wrong way for a short while and I immediately shut the power down. At the moment, when I try connect it to power, PWR…
ozgeneral
  • 223
  • 4
  • 13
1
vote
1 answer

RP3 doesn't load on HDMI - Mounting FUSE Control File System

I'd like to run my RP 3 on LCD 32". But when I try to run, loading is stopped after 9-10 seconds of starting up and the last line in the console is: "Mounting FUSE Control File System..." After this communicate console is stopped. Below, I show the…
gryzek
  • 131
  • 5
1
vote
3 answers

Raspberry pi 2 heats and does not boot (Power LED doesn't glow) after over-current dmesg

I was using my pi as a wifi router using USB wifi adapters and saw "USB over-current messages". I removed the USB devices and over-current messages stopped. however after some time. Pi restarted and doesn't boot now. The Red LED doesn't glow…
raptor
  • 11
  • 2
1
vote
2 answers

Fuse Mount Option "-nonempty" is Not Working

I have a setup where I need to log quite a bit of data on my Raspberry Pi. I have a 128GB USB stick that mounts to a folder called external where all my scripts/programs log to. This works well, except when the USB is removed the logs are written to…
CraftyMyner
  • 11
  • 1
  • 2
0
votes
3 answers

Raspberry Pi 3 Model B (not B+) USB polyfuse location

Usual problem - USB power has gone. Where is the fuse located on the board? The reduced schematics on the RPi webpage does not show the USB at all.
0___________
  • 240
  • 2
  • 10
0
votes
1 answer

"Transport endpoint is not connected" after a few seconds?

I set up a RPi as a SMB server with the official Raspbian jessie image (not lite). I installed samba and ntfs-3g for this purpose. The problem is whenever I start or reboot the RPi, after a few seconds all operations give the error "Transport…
iBug
  • 315
  • 2
  • 14
0
votes
1 answer

What to do if FUSE has no option NOFAIL in Raspian Bullseye 64bit?

When I use nofail in fstab with mp3fs (which is a filesystem that mounts flac and others as mp3 on-the-fly), I get the error fuse: unknown option 'nofail' My fstab: mp3fs#/mnt/mybook /mnt/mp3fs fuse…
bomben
  • 319
  • 1
  • 3
  • 13
0
votes
0 answers

Non-FUSE drivers for NTFS and exfat

I've run long benchmarks about write speed on a USB3 external HDD on a RPi4 (goal: use it as a NAS), with and without encryption. I've noticed that write speed is very fast with ext3, ext4 (it can reach the limit of the HDD speed, i.e. ~ 100 MB/sec…
Basj
  • 800
  • 3
  • 21
  • 49
0
votes
1 answer

Is my PI 3 B+ fine after this odd short-circuit behaviour?

I know that anything more than 5v touches any GPIO then it's dead but I was changing the wiring and accidentally plugged a 12v 2A (for motor supply) connector to a female connector which leads to GPIO pins 20 and 21 for a very short amount of time,…
BLOODHOUND
  • 5
  • 1