Arduino Stack Exchange
Arduino Stack Exchange

Questions tagged [rf]

Radio Frequency. Typically used to refer to the radio portion of the electromagnetic spectrum which is used for wireless communication. Strictly speaking though, RF can refer to any oscillation (electrical or otherwise) at the associated frequency.

157 questions
32
votes
1 answer

Whats the difference between RF options (wifi, xbee, NRF24L01)

When doing RF, you have many options. Three of the most basic are in the title box WiFi Xbee NRF24L01 What are the practical differences in using them. What is the purpose of each other and the pros and cons. What would you use depending on the…
user1584421
  • 1,425
  • 3
  • 26
  • 36
11
votes
4 answers

Choosing wireless tech for lowest possible lag

I am drafting a pub quiz project, where the Referee gives a signal and multiple players push their buttons. The first to push wins the right to give an answer. I want all buttons (referee's + X players) to be wireless. Since the best quiz players…
Brian G.
  • 273
  • 3
  • 10
9
votes
2 answers

RFID/NFC (13.56 MHz), is it possible to send raw bytes and receive response?

I'm trying to implement a card reader (i.e. credit cards) for shopping purposes, and AFAIK those cards are ISO 14443-A compliant (Mifare Classic 1K). I already made an Android app that can send custom APDU to read specific sectors by using raw…
TheAverageGuy
  • 91
  • 2
8
votes
3 answers

Manchester Library Won't Compile for Attiny85

I am creating a wireless sensor using an Attiny85. I want to send the data to an arduino uno, so I purchased the 315mhz rf link kit from spark fun. Since the Attiny85 does not have a TX I decided to use the Manchester library however it won't…
Joel
  • 523
  • 3
  • 15
6
votes
4 answers

RF remote control using VirtualWire on ATtiny85 running at 8MHz on internal oscillator

I'm trying to make an RF remote control using ATtiny85 running at 8MHz on internal oscillator, this cheap RF 434MHz transmitter module (like the one below), and VirtualWire lib, but had no success so far. So, before I go any further, is it…
Ricardo
  • 3,390
  • 2
  • 26
  • 55
6
votes
1 answer

Problems with transmission between ATtiny85 and Arduino Uno with 433MHz RF modules and Manchester

I am trying to transmit from an ATtiny85 running at 16MHz internal clock to an Arduino Uno with the Manchester Library. The problem is that the Arduino is not receiving any data. I have hooked an oscilloscope to the ATAD/DATA pin of the transmitter,…
sunny-lan
  • 161
  • 2
6
votes
5 answers

433mhz range optimization

I would like to get the best range possible from my 433MHz modules. After A LOT of searching and reading, I'm convinced I should be able to cover 10m indoors with free line of sight. [update] After some tips in the comments I changed a few things.…
Thijs
  • 432
  • 1
  • 6
  • 21
5
votes
3 answers

Decoding 2.4G RF remote controller?

There is tons of information on how IR remote controls work and how to use an Arduino to decode those signals and use any IR remote to suit your project. But I couldn't find much info about 2.4G RF remotes. I want to control a string of addressable…
ahmadx87
  • 549
  • 2
  • 9
  • 16
5
votes
0 answers

Manchester 433MHz Nano to ATTiny85

My transmitter is a Nano, the receiver is a Tiny85. I use a Logic Analyzer to check if stuff is moving, I can clearly see data coming in at the receiver. The receiver does not 'decode' the data, man.receiveComplete() is never True so in the end…
Thijs
  • 432
  • 1
  • 6
  • 21
5
votes
0 answers

Is it possible to use the DASH7 protocol in an arduino?

I've been reading about the protocol DASH7 but can't find much documentation about it. There seems to be a protocol stack called OpenTag writen in C and I want to know if there is something familiar written in arduino code and why can't I find a lot…
Rui Lima
  • 151
  • 1
4
votes
2 answers

How can I get ultra clean dc wall power for my arduino project?

I'm doing an rfid project that requires a read range of at least 5 inches or about 13cm. I'm using a nano with a usb port, a rfid reader from priority 1 design and a large antenna. The problem I'm running in to is that when I power the project from…
badweasel
  • 155
  • 1
  • 8
3
votes
0 answers

STM32 Nucleo-L432KC can't send data to Arduino Uno via nRF24L01 module

Hello everyone. First of all, I know you're going to tell me to send my question on the stm32duino forum. But I tried to enter the stm32duino forum and I didn't succeed (I think their forum is closed). So I'll be happy if you could try to help me…
Reshef
  • 31
  • 2
3
votes
1 answer

Attiny85 and 433Mhz RF

I have this cheap RF link that I had working with the Arduni UNO, but I wanted to make it smaller and ATTiny85 should do the trick. The RF module is connected (data pin) to PB3 on the ATTiny. But I am having some problems. It does not work, and I…
Jason94
  • 303
  • 1
  • 5
  • 11
3
votes
1 answer

How to program an nRFL01 RF module that is connected to a pc via a USB to UART/TTL adapter?

In a few of my previous questions I was told that the nRF24L01 RF Module can be connected to a pc using a USB to UART/TTL adapter. After a bit of research I understand that one way to use it is to connect it to an arduino- and then to use certain…
mjsxbo
  • 145
  • 1
  • 5
3
votes
1 answer

rf24 change order of data

I'm using two Arduinos with the rf24 modules. I want to control a process with those, but for now I'm just checking the connection. This is the code of the master: #include #include "nRF24L01.h" #include "RF24.h" unsigned char…
Luis Ramon Ramirez Rodriguez
  • 79
  • 1
  • 11
1
2 3
…
10 11